Polyamide resin is an important chemical raw material. The main process: the first two polylactic acid pump into the ingredients slot opening of the feed pump, the quantitative two acid pump into the reactor, the stirrer, while the use of heat conducting oil heating; while the mixture of ethylenediamine and hexamethylene diamine in a raw material barrel suction on reaction kettle with amine pot; when the temperature in the reaction kettle material up to 80 DEG C, open the canister valve with amine to kettle drop (drop control acceleration); in the process of adding amine, the temperature maintained at 130 DEG C. All material is cast after, continue to heat to 150 degrees Celsius and 1 insulation materials hours.
【技术实现步骤摘要】
②工艺过程简述首先将二聚酸用泵送入配料槽,开启进料泵,将定量的二聚酸泵入反应釜后,开启搅拌器,同时使用导热油加热;同时将原料桶中乙二胺和己二胺的混合液吸入反应釜上的加胺小罐中;当反应釜中料温达到80℃左右时,打开小罐底阀向釜中滴加胺(控制滴加速度);在加胺的过程中,料温保持在130℃以下。所有物料投完后,继续升温至物料达150℃并保温1小时。打开导热油进油阀,使物料继续升温至225℃并保温1小时。经检验,产品合格后,停掉搅拌器,缓慢开启冷凝阀门(抽真空至-0.1Mpa),将反应生成的水冷凝去除(该工序将产生不凝气G2-1和废水W2-1)。打开反应釜底阀,并打开氮气(企业自制)阀门,缓慢加压至0.18Mpa,将釜内物料全部放入中间贮罐中冷却至110℃,使用空气压缩机将料液压入造粒机,造粒成型即得产品(原料杂质中所含的脂肪酸均可参与该聚合反应)。该造粒过程为液态冷凝造粒工艺:物料进入造粒机后,由液体发布器分布成若干小滴到输送带上,同时由输送带下面的冷却水(温度为25℃)将小滴物料冷却至固态颗粒状。从输送带下来后即可得到树脂颗粒。本步骤年生产批次为1639批(一釜一批),本工序3釜同时生产。每批生产时间约12小时。以二聚酸计,聚合反应产品收率约为92%左右,转化率为97.1%。5000t/a聚氨酯胶粘剂项目工程分析⑵生产工艺流程①5000t/a聚氨酯胶粘剂项目生产工艺流程聚合:把己二酸、对苯二甲酸由人孔投入聚酯反应釜,然后由醇高位槽再投入乙二醇、1,4-丁二醇,约4小时搅拌升温到160℃开始反应。蒸出水后,再用8小时升温至220℃把水完全蒸出,通过冷凝工序将反应生 ...
【技术保护点】
一种聚酰胺树脂生产工艺。
【技术特征摘要】
1.一种聚酰胺树脂生产工艺。2.聚...
【专利技术属性】
技术研发人员:胡江海,张晓磊,于飞,
申请(专利权)人:宁夏际华环境安全科技有限公司,
类型:发明
国别省市:宁夏;64
还没有人留言评论。发表了对其他浏览者有用的留言会获得科技券。